Standard Socket Sizes

July 09, 2024 Post a Comment

Standard socket sizes

The most commonly used and sold SAE sizes for wrenches and sockets are:

What is the size chart for sockets?

3/8″ Drive	1/4″ Drive	1/2″ Drive
6mm	4.5mm	9mm
7mm	5mm	10mm
8mm	5.5mm	11mm
9mm	6mm	12mm

What are the 3 socket sizes?

Socket Drive Sizes Metric and Standard (SAE) sockets come in three available drive sizes: 1/4 inch, 3/8 inch, and 1/2 inch. The measurement refers to the size of the square used to attach the to socket to a wrench or a ratchet.

How do I know what size my socket set is?

It's important to note that socket sizes are actually given in two measurements, namely: The size of the drive socket (the part that attaches to the socket wrench). These are always given in imperial measurements, and will usually be either 1/4", 3/8", 1/2", 3/4" or 1".

Does SAE mean standard?

SAE, or standard, is used on most domestic models, while metric applies to foreign or non-domestic vehicles. Socket sets and wrench sets are among the most used tools in cases where size measuring differences are important. Notably, SAE tools are measured in fractions of inches, from 5/32 to 2 ½ inches.

What are the 3 common sizes of ratchets?

Available with different drive sizes — 1/4 inch, 1/2 inch and 3/8 inch — to operate different size sockets. Most operate with a geared drive; those with a higher tooth count let you operate the tool with a smaller swinging motion, which is useful when there's little room to move the handle.

Should I use 6 or 12 point sockets?

Answer: It's true that 12-point sockets are fine for most lightweight repairs, but heavy wrenching calls for a six-point socket. A six-point socket is much less likely to slip off a stubborn fastener or round over the corners. Here's why: (1) Six-point sockets have thicker walls, so they're less likely to flew.

What are the 3 types of sockets?

Three types of sockets are supported:

Stream sockets allow processes to communicate using TCP. A stream socket provides bidirectional, reliable, sequenced, and unduplicated flow of data with no record boundaries.
Datagram sockets allow processes to use UDP to communicate. ...
Raw sockets provide access to ICMP.

Are 3/4 and 19mm the same?

19mm = 3/4 inch. 20mm = 25/32 inch. 21mm = just over 13/16 inch. 22mm = almost 7/8 inch.

What is the most common size socket?

The most commonly used types are 8 mm, 10 mm and 14 mm sockets.

What are the 4 different types of sockets?

However, some of the commonest options you would find are 36mm sockets and 10mm sockets. Considering the standard sockets, you can find four common types, and they include 3/4 –inch, ½-inch, 3/8-inch, and ¼-inch sockets. Most of these options mentioned above come with bits that would fit Torx screws.

Are metric and SAE the same?

While the majority of bolt-type fasteners used in the United States conform to one or the other measurement scale, the difference between SAE and metric fasteners (and their corresponding sockets) is as profound as the difference between yards and meters: They are almost the same, but not quite.

What is a standard socket set?

A typical professional grade socket set in a metal box. It contains two ratcheting socket wrenches ( 1⁄4-inch and 1⁄2-inch), various extensions for each of the wrenches, an assortment of sockets for each wrench, and a variety of bits fitting on the smaller wrench for different types of screws.

What is a basic socket set?

What is a Socket Set? A socket set is designed to help mechanics loosen, tighten and remove any nuts or bolts that are in a vehicle or machine.

What is a 10mm socket in standard?

So what is a 10mm socket equivalent? The equivalent imperial size of a 10mm socket is a 3/8 socket. Imperial sizes are known as SAE (Society of Automotive Engineers) or Standard.

How do you tell if a bolt is SAE or metric?

This one has three slashes on the top of it or hash marks those are called that indicates that it's

What is ISO vs SAE?

There is no significant difference between ISO (International Standards Organization) or SAE (Society of Automotive Engineering). Both organizations provide test standards to allow the ability to reliably compare published filter ratings among manufacturers.

Can I use SAE 5w30 instead of SAE 30?

Can I Use 5W-30 Instead Of SAE 30? Both oils have a “30” hot viscosity rating. This means SAE 5W-30 oil has the same flow rate as SAE 30 at operating temp. So, technically it's fine to use SAE 5W-30 oil in place of SAE 30.

Whats bigger 3/8 or 1/4 socket?

3/8 is expressed as 0.375 as a decimal and 1/4 is expressed as 0.25 in its decimal form. It is clear that the value of 3/8 is more than 1/4. Hence, it is bigger.

What are 1/4 ratchets used for?

A 1/4-inch ratchet is best for smaller sockets and precision work. The most versatile ratchet is the 3/8-inch size. This ratchet size can accommodate sockets of all sizes. It is big enough to apply a lot of force, but it can still fit into tight spaces.